energy resources assignment

Energy Resources, Introduction, Sources, Types & Map

The primary energy source on Earth is the sun. Know about Energy Resources, Conventional and non-Conventional Energy Sources & their Maps in this article for the UPSC examination.

Table of Contents

Energy Resources

The traditional definition of energy is the capacity of a system to perform labour, but as energy can take many different forms, it is challenging to come up with a single, all-encompassing definition. It is an attribute of an item that can be changed or transferred from one object to another, but it cannot be created or destroyed. Energy comes from a variety of places.

Mineral fuels are necessary for the production of electricity, which is needed by industry, transportation, and other economic sectors. The traditional energy sources include nuclear energy minerals and fossil fuels including coal, petroleum, and natural gas. These conventional sources are finite, run out and exhaust with time.

Energy Resources Types

Natural sources of energy can be divided into two categories i.e, Conventional Sources of Energy and Non-Conventional Sources of Energy.

Difference between Conventional Sources of Energy and Non-Conventional Sources of Energy

Conventional energy sources.

One of the vital minerals, coal is primarily employed in the production of thermal energy and the smelting of iron ore. Gondwana and tertiary deposits are the two main geological eras in which coal can be found in rock sequences. In India, bituminous coal accounts for over 80% of the non-coking quality coal reserves.

The Damodar Valley is home to India’s most significant Gondwana coal deposits.They are located in the Jharkhand-Bengal coal belt, which has significant coalfields such as Raniganj, Jharia, Bokaro, Giridih, and Karanpura.The largest coal field is Jharia, followed by Raniganj. The Godavari, Mahanadi, and Sone river valleys are the others that are connected to coal. The most significant coal mining areas are Singrauli in Madhya Pradesh, Singareni in Telangana, Pandur in Andhra Pradesh, Talcher and Rampur in Odisha, Korba in Chhattisgarh, Talcher and Rampur in Odisha, Chanda-Wardha, Kamptee and Bander in Maharashtra.

Assam, Arunachal Pradesh, Meghalaya, and Nagaland all have tertiary coal deposits. It is obtained from the Meghalayan regions of Darangiri, Cherrapunji, Mewlong, and Langrin; upper Assamese regions of Makum, Jaipur, and Nazira; the Arunachal Pradesh regions of Namchik-Namphuk; and Kalakot (Jammu and Kashmir). In addition, coastal regions in Gujarat, Jammu and Kashmir, Tamil Nadu, and Pondicherry have brown coal, often known as lignite.

2. Petroleum

Hydrocarbons in liquid and gaseous forms that vary in chemical composition, colour, and specific gravity make up crude petroleum. For all internal combustion engines in automobiles, trains, and aeroplanes, it is a necessary source of energy. Petrochemical industries use its myriad byproducts to make fertiliser, synthetic rubber, synthetic fibre, pharmaceuticals, vaseline, lubricants, wax, soap, and cosmetics. Tertiary-era sedimentary rocks contain crude petroleum.

The Oil and Natural Gas Commission was established in 1956, and since then, oil exploration and production have been actively pursued. The sole oil-producing refinery until 1956 was the Digboi in Assam, but things changed after 1956. New oil reserves have been discovered in the country’s extreme western and eastern regions in recent years.

Digboi, Naharkatiya, and Moran are significant oil-producing regions in Assam. Gujarat has several significant oil reserves, including Ankleshwar, Kalol, Mehsana, Nawagam, Kosamba, and Lunej. Mumbai High, which is located 160 kilometres off the coast of Mumbai, was founded in 1973, and production there started in 1976.

In exploratory wells in the Krishna-Godavari and Kaveri basins on the east coast, oil and natural gas have been discovered. Crude oil, which has numerous contaminants, is the oil that is extracted from the wells. It can’t be used straight up. It requires improvement. India has two different kinds of refineries: (a) market-based and (b) field-based. Field-based refineries are illustrated by Digboi, while market-based refineries are illustrated by Barauni.

3. Natural Gas

In order to transport and market natural gas, the Gas Authority of India Limited was established as a public sector enterprise in 1984. It is found in all oil fields alongside oil, however, there are exclusive reserves in Tripura, Rajasthan, Gujarat, and Maharashtra as well as along the eastern coast (Tamil Nadu, Odisha, and Andhra Pradesh).

Energy Resources Maps

Below are the Maps of the Energy Resources Maps of India

Non-Conventional Energy Sources

Coal, petroleum, natural gas, and nuclear energy all use finite raw materials as their primary energy source. Only renewable energy sources like sun, wind, hydro geothermal, and biomass are considered sustainable energy sources. These energy sources are more environmentally responsible and evenly dispersed. After the initial cost is covered, non-conventional energy sources will offer more consistent, eco-friendly, and less expensive energy.

1. Nuclear Energy

In recent years, nuclear energy has shown to be a reliable source. Uranium and thorium are significant minerals utilised in the production of nuclear energy. The Dharwar rocks contain uranium reserves. Geographically, it is known that uranium ores can be found along the Singbhum Copper belt in a number of areas. Additionally, it can be found in the districts of Kullu in Himachal Pradesh, Durg in Chhattisgarh, Alwar, and Jhunjhunu in Rajasthan, and Udaipur, Alwar, and Jhunjhunu in Rajasthan. Monazite and ilmenite in the beach sands of Kerala and Tamil Nadu’s coasts are the main sources of thorium. The richest monazite deposits in the world are found in the Keralan districts of Palakkad and Kollam, close to Vishakhapatnam in Andhra Pradesh, and near the Mahanadi river delta in Odisha.

The Atomic Energy Commission was founded in 1948, but advancements couldn’t be achieved until the Atomic Energy Institute in Trombay was founded in 1954 and later renamed the Bhabha Atomic Research Centre in 1967. The significant nuclear energy projects are those at Tarapur in Maharashtra, Rahatbhata near Kota in Rajasthan, Kalpakkam in Tamil Nadu, Narora in Uttar Pradesh, Kaiga in Karnataka, and Kakarapara in Gujarat.

2. Solar Energy

Solar energy is created by harnessing the sun’s rays in photovoltaic cells. Photovoltaics and solar thermal technology are two methods that are thought to be particularly effective in harnessing solar energy. Comparatively speaking, solar thermal energy has some advantages over all other non-renewable energy sources. It is affordable, environmentally friendly, and simple to build.

Solar power is 10% more efficient than nuclear power and 7% more efficient than coal or oil-based systems. Appliances like heaters, crop dryers, cookers, etc. typically use it more. Gujarat and Rajasthan in western India have the most potential for the growth of solar energy.

3. Wind Power

Wind power is a limitless, pollution-free source of electricity. The process of converting wind energy is straightforward. Through the use of turbines, wind energy’s kinetic energy is transformed into electrical energy. As a source of energy, the trade winds, westerlies, and seasonal wind patterns like the monsoon have all been exploited.

Other than these, it is also possible to generate power using local winds, land breezes, and sea breezes. India has already begun producing wind energy. It has an ambitious plan to erect 250 wind turbines with a combined 45 megawatts of power in 12 suitable spots, primarily along the coast. To reduce the cost of oil imports, India’s Ministry of Non-Conventional Sources of Energy is fostering the growth of wind energy.

More than 50,000 megawatts of wind energy can be produced in India, of which only one-fourth is feasible to use. Conditions are favourable for wind energy in Rajasthan, Gujarat, Maharashtra, and Karnataka.

4. Tidal and Wave Energy

Ocean currents are a never-ending source of energy. Continuous efforts have been made from the beginning of the seventeenth and eighteenth centuries to develop a more effective energy system using constant tidal waves and ocean currents.

The west coast of India is known to experience large tidal waves. As a result, India has a lot of potential for tidal energy production along the coasts, but this potential has not yet been realised.

5. Geothermal Energy

Extreme heat is emitted as magma from the earth’s interior rises to the surface. It is possible to successfully harness and transform this thermal energy into electrical energy. In addition to this, thermal energy is also produced from the hot water that spews from gyser wells. It is commonly referred to as geothermal energy. These days, one of the main energy sources that can be created as a backup supply is thought to be this energy. Since the Middle Ages, people have been using the hot springs and geysers. At Manikaran in Himachal Pradesh, an Indian geothermal energy plant has been put into operation.

6. Bio-energy

Bio-energy is defined as energy produced from biological materials, such as municipal, industrial, and other wastes as well as agricultural residues. A potential source of energy conversion is bioenergy.

It can be transformed into gas for cooking, heat energy, or electrical energy. Along with processing waste and garbage, it will also generate energy. This would boost the quality of life for rural residents in developing nations, lessen environmental pollution, increase independence, and ease the demand for fuel wood. Okhla in Delhi is one such initiative that turns garbage from the city into energy.

Energy Resources Conservation

The difficulty of sustainable development necessitates fusing the pursuit of economic growth with environmental considerations. Traditional resource usage practices generate a significant amount of trash and contribute to other environmental issues. Therefore, conserving resources for future generations is necessary for sustainable growth. The necessity to save resources is critical.

Alternative energy sources including solar, wind, wave and geothermal power provide an endless source of energy. To replace the finite resources, these should be developed. Utilizing scrap metals will allow for the recycling of metals in the case of metallic minerals. Utilizing scrap is particularly important for metals like copper, lead, and zinc, where India has limited deposits. Utilizing alternatives for rare metals may also cut down on usage. Reduced export of strategic and rare minerals is necessary to extend the useful life of the current reserve.

Energy Resources UPSC

Conserving means taking care of and preserving these resources for future generations. As a UPSC aspirant, you should be well aware of the location of various oil refineries and the collaboration of India with various countries in upgrading the refineries. Also, the conservation of energy on an individual level is crucial and switching from conventional to non-conventional energy or alternative energy resources should be encouraged and emphasized. This topic of geography holds immense importance from both Prelims and Mains point of View. The details in the article would help candidates preparing for UPSC 2023.

Energy Resources FAQs

Q) What is the primary sources of energy?

Ans. Sun is the primary source of energy.

Q) What do you mean by conventional sources of energy?

Ans. These resources are exhaustible and run out eventually. Examples are Coal, Petroleum.

Q) Is Nuclear energy conventional or non-conventional resources?

Ans. Nuclear energy is a non-conventional resource Examples are Uranium and Thorium.

Q) Where is the Digboi refinery located?

Ans. It is located in Assam.

Q) What are examples of non-conventional resources?

Ans. Non-conventional resources include solar energy, bioenergy, tidal energy and wind energy.

What is the primary sources of energy?

Sun is the primary source of energy

What do you mean by conventional sources of energy?

These resources are exhaustible and run out eventually. Examples are Coal, Petroleum.

Is Nuclear energy conventional or non-conventional resources?

Nuclear energy is a non-conventional resource Examples are Uranium and Thorium.

Where is the Digboi refinery located?

It is located in Assam.

What are examples of non-conventional resources?

Non-conventional resources include solar energy, bioenergy, tidal energy and wind energy.

BPSC Exam 2024

BPSC 70th Notification
BPSC 69th Exam Analysis
BPSC Admit Card
BPSC Syllabus
BPSC Exam Pattern
BPSC Cut Off
BPSC Question Papers

IB ACIO Exam

IB ACIO Salary
IB ACIO Syllabus

CSIR SO ASO Exam

CSIR SO ASO Exam 2024
CSIR SO ASO Result 2024
CSIR SO ASO Exam Date
CSIR SO ASO Question Paper
CSIR SO ASO Answer key 2024
CSIR SO ASO Exam Date 2024
CSIR SO ASO Syllabus 2024

IMPORTANT EXAMS

Terms & Conditions
Return & Refund Policy
Privacy Policy

Energy resources: An introduction to energy resources

An introduction to energy resources

Understanding energy resources involves considering all types of energy source from various scientific and technological standpoints, with a focus on the uses, limitations and consequences of using energy that is available to humanity. This course sets the scene by considering how much energy human society uses and the basic concepts of energy , work , power and efficiency, then briefly investigates the different types of energy available, their sources and renewability.

This OpenLearn course provides a sample of level 2 study in Science

Learning outcomes

After studying this course, you should be able to:

understand the difference between energy and power , and their units and prefixes

state the relative contributions of different natural energy sources to the global energy budget

describe the contribution of photosynthesis to the carbon cycle , and distinguish the terrestrial and marine parts of the cycle

discuss the issues involved in concentrating, storing and transporting energy

recognise which energy resources have a low energy density , and which have a high energy density .

1 Energy use

Until about 8000 years ago humans relied on hunting and gathering for food, and burning wood to keep warm. Their exact energy demands can at best only be estimated but to survive they probably needed about as much energy as it takes to run a couple of ordinary domestic light bulbs continuously. Later, agriculture developed, and although wood was still the chief fuel, animal power , animal dung and charcoal were also used. Even today, such energy sources based on natural biomass dominate the lives of human populations in the so-called 'Third World' or 'developing countries'. The 19th century heralded a large increase in energy use in what were to become industrialised countries ( Figure 1.1 ), particularly the use of coal. Homes and other buildings were heated; factories and railways were powered by steam engines ( Figure 1.2 ); mining and chemical industries developed and agriculture became more mechanised. The emergence of technological societies in the 20th century resulted in an even larger increase in energy use for manufacturing, agriculture, transport and a host of other applications. In technologically advanced countries the largest increases have been in using gas for heating, oil products for transport, and electricity as a convenient means of transferring energy generated by a variety of sources ( Figure 1.3 ).

It is important to remember that the primary energy released by all forms of energy resources is not the amount that performs useful tasks: it is the total amount of energy released by human activity . Energy use and conversion, as you will see, can never be fully efficient. For that reason, the energy consumed usefully by society is considerably less than primary energy released: you will find that we refer to both primary energy and energy consumption (sometimes demand), depending on the context.

World population rose from some 5 million 10 000 years ago, through 1 billion in the 19th century to 6.5 billion in 2005. This rapid increase in population, together with a sharp increase in the demand that each person in the developed world has for energy , led to the dramatic rise in global energy consumption ( Figure 1.1 ).

All the Earth's physical resources, for example metals in ores, water supplies and building stone, depend on using energy to extract, process and transport them. In effect, the ability to extract and use the Earth's physical resources depends on whether there is a ready supply of energy at the right price. If there were a limitless supply of cheap energy we could turn the entire stock of all physical resources into reserves. One aim of this book, and indeed the whole course, is to examine the limits that exist in reality: some are governed by physical laws, others depend on economics and there are also limits posed by sustaining the Earth's environmental conditions on which life depends.

2 Energy, work, power and efficiency

In everyday speech we often refer colloquially to the powerful politician, the energetic child, the working mother and the efficient administrator. We use these terms imprecisely, and often wrongly, compared with their scientific definitions.

2.1 Some basic concepts

Energy is defined as the capacity to do work , and work is even more precisely defined as a force acting on an object that causes its displacement , and is calculated from force × distance . Work is therefore the foundation for scientific study of motion and change.

The unit of work is the same as that for energy : the joule (J) . Yet a joule, unlike the units of mass, length or time, is not a fundamental unit. Working out the joule in fundamental units takes us to the root of the physics involved. The definition of work ( force × distance) shows that one joule is actually one newton metre (N m).

Force is mass × acceleration , so one newton is the force that gives a mass of one kilogram (kg) an acceleration of one metre per second per second (m s −2 ) , and is therefore equivalent to 1 kg m s −2 .

However, work is not just mechanical movement, such as moving sacks of flour around or turning a wheel. It is also involved in heating a substance (vibrating its molecules), changing its state (melting and boiling) and compressing it, along with many other phenomena.

As an example of the connection between work and energy consider the energy bound up with a photon of light that strikes the photoelectric cell in a solarpowered pocket calculator. Some of that photon's energy becomes an electrical current that contributes to the calculator's microchip executing a calculation. However, most of the original light energy goes to heating up the cell and the liquid crystal display that shows the answer, and there might even be a beep of sound when the calculation is complete. During this process a tiny amount of work is done, but the form of the energy has changed, from the otherwise limitless potential of light to travel an infinite distance through a vacuum, never losing its 'capacity to do work ', to the motion of particles of matter. The last change is eventually expressed by a minuscule rise in temperature in and around the calculator, which ultimately dissipates to help heat up the rest of the Universe! Energy can neither be created or destroyed (the Law of Conservation of Energy ) so the energy of the photon doesn't disappear but is spread far and wide. Although eternal, in practice it is beyond recovery: useful energy in a high grade form is degraded through the material work that it has done.

Energy takes many natural forms: light, heat, sound, mechanical movement ( kinetic energy ), that gained by position in a gravitational field ( potential energy ), the movement of electrons (electricity), chemical energy , that released through Einstein's famous matter- energy conversion E = mc 2 (nuclear energy ) and a great many more. In this book we deal mainly with the forms of energy that are available at sufficiently high grade to be able to do useful work . An implicit theme is that all energy sources are themselves products of work done naturally:

Chemical energy — ' fossil fuels ', such as coal and petroleum, and 'biofuels', such as wood, are the products of conversion of solar energy into the energy of chemical combination through photosynthesis by plants;

Nuclear energy — nuclear fuels are heavy radioactive isotopes produced by thermonuclear fusion in long-dead stars that became supernovae;

Geothermal energy comes from heat produced by the natural decay of radioactive isotopes distributed at very low concentrations in the Earth;

Solar energy is emitted by thermonuclear fusion within the Sun;

Tidal energy is essentially the work done by the gravitational fields of the Moon and Sun on the oceans;

Wind and wave energy are solar energy converted into work done by the Earth's atmosphere and oceans;

Hydro energy relies on work done by solar energy in evaporating water that falls as rain or snow at high topographic elevations, which in turn has gravitational potential energy .

Every application that 'uses' energy is in fact converting one form of energy into other forms. Some of this energy conversion is useful, some is not. A kettle boils water, but it may also 'sing' (sound energy ) and heat up itself. A hydroelectric power station turns the kinetic energy of moving water into electricity through generators, but at the same time friction between the moving parts of the generators produces heat and sound. The heat and sound are degraded and less useful forms of energy .

Which energy changes take place when an electric kettle boils water?

Electrical energy is first converted into heat energy as it increases the vibrational movement of atoms in the metal heating element. Heat is conducted through the element into the water, making the water molecules vibrate more, thereby raising its temperature. Finally, heat energy converts water into steam.

The point to be grasped here is that changes of energy from one form to another are commonplace in everyday life.

Power is the rate at which energy is delivered or work is done . It is worth noting the difference between power and energy : energy is an amount of work done over an indefinite time interval and power is the rate at which energy is converted, i.e. the amount used or made available per second. The units for measuring energy and power are summarised in Box 1.1 below.

Box 1.1 Units of energy and power

All forms of energy are measured in the same unit, the joule (J). A joule is the same amount of energy irrespective of which form (light, sound, electrical, and so on) that energy takes.

Recalling the earlier definitions in this section, when 1 kg falls 1 m at the acceleration due to gravity at the Earth's surface (9.81 m s −2 ), the work done ( force × distance) is mass in kg × acceleration due to gravity in m s −2 × height in m, i.e.:

So a joule is equivalent to the work done when a mass of (1/9.81) kg or 0.102 kg falls through a metre: a mass about the size of the apple reputed to have fallen on Isaac Newton 's head to inspire his theory of gravity! A joule is a small amount of energy so when considering national or international energy use, large multiples of the joule are needed, and these are named in the metric (SI) system using standard prefixes ( Table 1.1 ).

There is another energy unit that will be used occasionally in this book, the tonne oil equivalent (toe) . This is often used by energy statisticians as a convenient means of comparing amounts of energy available from fuels other than oil. One toe is the chemical energy contained in one tonne of oil , and equates approximately to 4.19 × 10 10 J (i.e. 41.9 GJ).

Being a rate, power is measured in joules converted per second (J s −1 ), called watts (W). One watt is equivalent to one joule per second . Note that if you are hit on the head by a falling apple, even though its energy is only about 1 J, the impact is almost instantaneous, so its power is high. Just as a joule is a small unit of energy , so a watt is a small unit of power . Larger quantities of power are quoted using the same prefixes as energy , as given in Table 1.1.

An electric supply of 1 kW will run a microwave oven, or around 10 light bulbs. Working really hard, the human body can deliver about 1 kW for a very short period of time.

Every three months or so most people in the UK receive an electricity bill, which states the number of 'Units' of electricity they have used, as measured by their electricity meter. The 'Units' quoted are kilowatt hours (kW h). But what, in purely physical terms, does 1 kW h represent? One kilowatt hour is the energy delivered at a power of 1 kW for one hour. This is equivalent to 1 kJ per second for an hour, i.e. 3600 kJ.

In practical terms, you might think that one kW h was a measure of all the work done around your home by various appliances in an hour. You would be very disappointed, because not one of them is perfectly efficient. In fact over 70% of each 'Unit' would ultimately have been lost to heating the rest of the Universe without doing any useful work . As you will see below, generating and then transmitting the electrical energy to your home will have been inefficient too, so a high proportion of your bill had been spent on work that was of no practical use to you.

When we convert energy from one form to another, the output that is useful to us is never as much as the energy input. The ratio of the useful output to the input (i.e. the ratio of useful work done to the energy supplied ) is called the energy efficiency of the process and is usually expressed as a percentage. Every natural process involves a change in grade of energy through the work that it does, but one joule always ends up as one joule, because of the Law of Conservation of Energy . Ignoring this transformation in grade, energy conversion could be said to be 100% efficient. But that misses the point. A perfect energychanging machine would get out as much useful energy as was put in, so it would be 100% efficient, but such a machine does not and probably cannot exist.

Efficiency can be as high as 90% in a water turbine, but only around 35-40% in a coal-fired power station. The energy delivered to do useful work is considerably less than the primary energy consumed in electricity generation.

2.2 Present-day energy use

Global annual consumption of all forms of primary energy increased more than tenfold during the 20th century ( Figure 1.1 ), and by the year 2002 reached an estimated 451 EJ. About three-quarters of this energy came from coal, oil and gas ( Figure 1.4 ).

If the global annual energy consumption is 451 EJ, what would be the average rate of consumption each second of every day, i.e. the global power demand?

Make a note of these equivalent amounts, as you will be comparing them with the energy and power available from various sources later.

With a global population of 6.5 billion, each person's 'drain' on primary energy is, on average, around 73 GJ per year. But globally, there are major regional differences in energy consumption ( Figure 1.5 a). Developed countries, with industrial as well as domestic demands, use energy in vast quantities and at alarming rates. In North America it is around 350 GJ per person per year, nearly five times the global average, and totalling around 28% of global energy use by about 4.5% of world population. People in Europe and the former Soviet Union use about double the global average. Figure 1.5 b, which shows the amount of lighting seen from space at night, gives a graphic picture of the inequalities of energy use.

In 2002, UK primary energy used was the equivalent of 9.7 EJ: about 164 GJ for each of the 59 million people in the UK, just over double the global average. About one-fifth of the UK's primary energy requirement is used in the home, 30% lost in conversion and most of the rest for services, transport and industry (Figure 1.6 below).

2.3 Global power demand

In Section 2.2 we calculated a value of 14.3 TW for the average global requirement for primary power in 2002.

For a global population at this time of 6.2 billion, how much primary power was needed to support the activities of each person in the world, on average?

Dividing 14.3 TW (14.3 × 10 12 W) by the world population of 6.2 × 10 9 gives an average primary power requirement of 2.3 kW per person.

The average global figure of 2.3 kW per person is about five times less than that needed to enable each North American citizen to sustain the lifestyle to which he or she has grown accustomed. If every individual in the world were to demand as much energy as the average person uses in North America, the global energy supply industries would require a fivefold increase in their use of primary energy sources. Even more daunting is the prospect of continued growth of both world population and per capita energy demand.

3 Sources of energy from the natural environment

The natural environment itself is bathed in energy from other sources. Standing on a cliff top on a bright spring day you can feel the warmth of the Sun and the freshness of the breeze and hear the crashing of breaking waves below. All these energetic processes can be compared in terms of energy and power .

In order to put the total global energy supply and demand into proper perspective we need to know the contribution made by different natural energy sources to the Earth's energy supply. By far the most important source on Earth is the Sun, but some energy comes from the gravitational attraction between Sun, Moon and Earth, and some from the Earth's own internal heat. Figure 1.7 gives all the data on natural energy sources you will need in working through this section.

3.1 Solar radiation

Over 99.9% of the energy available at the Earth's surface comes from the Sun. Solar energy emanates from a vast nuclear powerhouse producing heat, light and other types of electromagnetic radiation released by nuclear reactions. The Sun's power output is enormous, some 10 14 TW, but only a tiny proportion, about 1.7 × 10 5 TW, reaches the Earth. About a third of this is reflected by clouds and the Earth's surface directly back into space ( Figure 1.7 ).

How much energy reaches the Earth (surface and atmosphere together) from the Sun each year? (Don't forget the numbers in Figure 1.7 are in terms of power .)

The Sun supplies 1.7 × 10 5 TW to the Earth, of which 1.1 × 10 5 TW enters the Earth's system (0.3 × 10 5 TW to atmospheric heating + 0.8 × 10 5 TW absorbed at the surface, see Figure 1.7). 1.1 × 10 5 TW is equivalent to 1.1 × 10 17 J s −1 , and since there are 3.15 × 10 7 s in a year, the Sun's annual energy supply is 3.15 × 10 7 s × 1.1 × 10 17 J s −1 = 3.5 × 10 24 J or 3.5 × 10 6 EJ.

If all the solar energy that reaches the Earth could be harnessed, current human needs would be supplied thousands of times over. The reason it cannot is explained later.

Solar radiation is potentially available as an energy resource either as direct solar energy using solar cells or heating devices ( Figure 1.8 ), or naturally through plant and animal growth. Some 50 000 TW of absorbed solar radiation is transferred back into the atmosphere through evaporation and convection ( Figure 1.7 ). Some of this energy reappears in a usable form when water eventually returns to the surface as precipitation. This energy is largely dissipated as frictional heat and sound during the return flow of the water to the oceans, but it can also be harnessed as hydropower , an indirect form of solar energy .

However, if the electrical power requirement of an average British household — around 3 kW — came from solar energy alone, even if every day were sunny each dwelling in Britain would need about 100 m 2 of solar panels, on a very large south-facing roof. But is solar energy the answer to energy supply in sunnier parts of the world?

California has an area of about 4.1 × 10 11 m 2 . Even if the Sun shines there for 12 hours each and every day of the year, what percentage of California's land surface area would need to be covered by solar panels to supply the energy demands of the whole of the USA? The USA used 96.5 EJ of energy in 2003. A 10% efficient, metre-square solar panel would supply 31 J every second.

Assuming that solar panels operated for 1.6 × 10 7 seconds a year (12 hours a day), one such panel would supply about 5 × 10 8 J. The USA would therefore need around 2.0 × 10 11 such panels (i.e. 96.5 × 10 18 J divided by 5 × 10 8 J). Since the area of California is 4.1 × 10 11 m 2 , about 50% of it would have to be covered by solar panels to meet US energy demand. (The assumptions we have made are so unrealistic that the figure would be much higher, were a ' solar energy only' scheme to be implemented.)

What happens to the solar energy that reaches the Earth's surface? Because the Earth is a sphere, the heating effect of the Sun is greater in equatorial latitudes than at the poles. Coupled with the Earth's rotation, this produces winds which blow between belts of high and low atmospheric pressure. About 10% of the Earth's absorbed solar power (10 000 TW) gives rise to winds ( Figure 1.7 ). Much of the energy of winds is dissipated as heat, but some 10% of this wind power (i.e. 1000 TW) is transferred to waves through frictional effects at the sea surface.

Could the world be supplied from wind and wave power one day?

Theoretically, yes, but practically, no. Total global wind power amounts to 10 000 TW, i.e. around one thousand times human power demands. However, tapping wind power over one-thousandth of the world's surface (some 510 000 km 2 or over twice the size of Britain) would be a colossal undertaking and the process would have to be fully efficient. Similar arguments apply to wave power , except that here a maximum of 1000 TW is theoretically available (100 times annual demand), requiring twice the surface area of the Mediterranean Sea to be tapped at 100% efficiency.

Tides are caused by the gravitational pull of the Moon and to a lesser extent the Sun. Although tides affect all fluid bodies on Earth in some measure, including some parts of the solid Earth itself, their main effect is on the seas and oceans. Ultimately the kinetic energy of tides is converted into heat, mainly through friction between water and the sea bed. Tides can be exploited as an energy resource, and the total amount of power available can be calculated from knowledge of the gravitational effects of the Earth-Moon-Sun system. At about 2.7 TW, it is many orders of magnitude less than the power of solar radiation ( Figure 1.7 ) and less than 20% of the current power demand for human activities.

3.3 The Earth's internal heat

The occurrence of both volcanoes and hot springs shows that the Earth's interior is hot, producing molten rock at temperatures up to 1250 °C, and also superheated steam. However, these phenomena are mainly confined to several narrow zones along the world's active plate boundaries. Many measurements have now been made of the amount of heat flowing from the Earth's interior. Outside the distinctive zones mentioned above, heat flow varies from 40-120 milliwatts per square metre (mW m −2 ), largely generated by the decay of long-lived radioactive isotopes within the Earth. The total power output from the Earth's interior, estimated at some 10 TW, is many orders of magnitude less than the total incident solar power ( Figure 1.7 ).

Could the global energy requirement come entirely from geothermal sources eventually?

No. At 10 TW, this source is roughly only the same as current power demand for human activities. All of it would need to be used (including that from the ocean floor) at an impossible 100% efficiency.

4 Fossil fuels

Part of the incoming solar energy becomes stored in fossil fuels (oil, gas and coal: Figure 1.7 ). To understand why fossil fuels exist you need first to know where the major stores of carbon are on the planet and how, through organic activity, this carbon becomes fixed in rocks and thus liable to be stored for geologically long periods.

4.1 Natural stores of carbon

The major natural stores of carbon (called 'reservoirs') are shown below in Figure 1.9.

Which two reservoirs contain most of the carbon?

Carbonate rocks and preserved organic carbon.

Carbon is being exchanged continually between the principal reservoirs shown in Figure 1.9 . However, since most stored carbon is held in carbonate rocks and preserved organic carbon (POC), the principal carbon exchange over geological timescales (millions of years) is from the surface reservoirs into limestones and POC.

For our purposes two exchange systems can be distinguished (somewhat artificially because in practice the two are intimately linked):

the land-based or terrestrial system in which carbon is exchanged between land plants and both the soil and the atmosphere;

the marine system which exchanges carbon within the oceans and between the oceans and the atmosphere.

Together they form the natural carbon cycle .

4.2 The terrestrial carbon cycle

Figure 1.10 shows the rates of natural carbon exchange between the terrestrial system and the atmosphere.

Using the data in Figure 1.10 , calculate whether there is a net movement of carbon into or out of the atmosphere, as far as the terrestrial carbon cycle is concerned.

Figure 1.10 shows that 120 × 10 12 kg yr −1 flows from land plants and soil and plant detritus into the atmosphere, and 120 × 10 12 kg yr −1 moves from the atmosphere into land plants. Therefore, as far as the terrestrial carbon cycle is concerned, there is on average a net balance of carbon flow. (We show later how special conditions allow accumulations of plant material.)

The average time that carbon stays in a reservoir before moving to another reservoir is known as the residence time , and is measured by the amount of carbon in the reservoir divided by the transfer rate of carbon between it and other reservoirs.

Question 10

What is the average residence time of land-derived carbon in the atmosphere, which contains about 760 × 10 12 kg of carbon?

The residence time of terrestrial carbon in the atmosphere, as defined above, is 760 × 10 12 kg/120 × 10 12 kg yr −1 , or just over 6 years, on average.

As Figure 1.10 shows, each year land plants take 120 × 10 12 kg of carbon from the atmosphere. In the next section we consider how exactly carbon is exchanged between the atmosphere and plants.

4.3 Photosynthesis, respiration and decay

Green plants absorb solar radiation and use its energy to fuel photosynthesis — a chemical reaction in which carbon dioxide (CO 2 ) from the atmosphere is combined with water (H 2 O) to form carbohydrates with the general formula C n H 2n O n . One of the simplest carbohydrates , glucose, has the chemical formula C 6 H 12 O 6 , so in its simplest form photosynthesis can be represented by the balanced chemical equation:

The oxygen produced by this reaction is released by plants into the atmosphere. Carbohydrates act as a store of energy for plants and also for other organisms that eat them. Such organisms use oxygen from the air to react with the carbohydrates (and other substances) to liberate energy by a process called respiration . During respiration, carbon dioxide and water are returned to the atmosphere. Expressed in the simplest chemical terms, the balanced reaction is:

Carbon exchanges or fluxes link the chemistry of the atmosphere with plant and animal chemistry. The carbon taken from the atmosphere ( fixed ) by plants enables them to grow, but in addition much of it enters the food chain as either living or dead material. Living plants are eaten by herbivores which themselves may become food for carnivores. The dead material provides food for the decomposers (bacteria and fungi) that live in plant detritus, in the soil, and on the rotting remains of dead animals. Almost all organisms return some carbon to the atmosphere through respiration, but by far the greatest contribution comes from the activities of the decomposers. The timescale by which this takes place is measured in months and years, so plant and animal material is not normally available to be preserved as fossil fuels .

However, if organic matter decays in an environment where the oxygen supply is limited, carbohydrates cannot be broken down completely to form water and carbon dioxide. In this special oxygen-poor ( anoxic ) environment, a carbohydrate comparatively enriched in carbon may be produced. For example, within the waterlogged environment of a swamp (mire), cellulose (a common constituent of plants) can be broken down according to the following reaction:

The residue produced, C 8 H 10 O 5 is relatively enriched in carbon compared with the original cellulose (C 6 H 10 O 5 ). This breakdown reaction releases methane (CH 4 ), as well as carbon dioxide and water. Methane is an organic compound containing carbon and hydrogen but no oxygen; one of a family of organic compounds known as hydrocarbons . So anoxic environments prevent some fixed carbon returning to the atmosphere as CO 2 , and these hydrocarbons together with carbon-rich residues represent a chemical half-way-house within the carbon cycle , which make carbon available to form the basis for fossil fuels .

Although significant layers of decaying plant debris are found on the floor of modern forests, these are often oxygen-rich environments thanks to the constant reworking of decaying material by plants and animals, fungi and bacteria. However, one modern environment with which you are probably familiar does contain plant material decaying in anoxic conditions — the peat bog.This is where useful preservation of terrestrial carbon occurs.

4.4 The marine carbon cycle

The ocean stores much more carbon than the terrestrial system ( Figure 1.9 ). How is this marine carbon fixed into organic carbon within the sediments, and what are the main reasons for marine carbon fluxes? Figure 1.11 shows the rates of natural carbon exchange within the ocean and between the ocean and the atmosphere.

Question 11

From the data presented in Figure 1.11 , is there a net movement of carbon into or out of the atmosphere from the ocean?

Figure 1.11 shows that 90-100 × 10 12 kg of carbon flows each year from ocean surface waters into the atmosphere, while roughly the same amount of carbon moves from the atmosphere into the ocean: there is no net movement.

Carbon dioxide is constantly being exchanged between the atmosphere and the upper levels of the oceans, by physical and by chemical processes. At the base of the food chain that produces organic material in the oceans are the marine phytoplankton (microscopic water-borne plant life) which require dissolved CO 2 for photosynthesis . The process also requires solar energy , so phytoplankton can live only in the sunlit upper parts of the ocean. Their photosynthesis releases oxygen, which dissolves in seawater. The productivity of phytoplankton depends on sunlight, temperature and supply of nutrients, and therefore varies geographically.

Carbon dioxide is more soluble in cold water than it is in warm water, so the concentration of dissolved CO 2 tends to be higher in cold polar waters than in warm tropical waters. Cold, dense polar water sinks and flows under the influence of gravity along the ocean floor towards the Equator. It returns to the surface by upwellings at various places in the oceans, to supply nutrients and promote unusually high phytoplankton productivity there.

Zooplankton (water-borne animal life, mostly microscopic) and higher marine organisms consume these phytoplankton. The dead remains of phytoplankton, zooplankton and larger organisms sink through the water column, transferring carbon from the upper few hundred metres towards the ocean depths. However, little of this organic matter gets a chance to accumulate on the ocean floor. It provides food for filter feeders in deep water and on the ocean floor, and through them for predatory animals, and ultimately feeds the ubiquitous decomposers. All these organisms release CO 2 back into solution through respiration. As Figure 1.11 shows, only a small proportion of the marine carbon cycle , 0.2 × 10 12 kg yr −1 of carbon, is incorporated into marine sediments.

Question 12

Assume that 0.2 × 10 12 kg yr −1 of carbon were incorporated into marine carbonates and fossil fuels in proportion to their present-day amounts ( Figure 1.9 ). How long would it have taken to deposit all the carbon found in the current global store of POC, of which fossil fuels are a part?

We know from Figure 1.9 that the global carbonate store is some 4 × 10 19 kg of carbon, and that the POC store is some 10 19 kg of carbon, a total of 5 × 10 19 kg of carbon. If carbon were deposited into each reservoir in proportion, the rate of deposition of carbon into POC would be:

At this rate, it would have taken 1 × 10 19 kg/0.04 × 10 12 kg yr −1 , which is 2.5 × 10 8 years, i.e. 250 million years to deposit enough carbon to form the global POC store, which includes fossil fuels .

However, not all fossil fuel formed in the marine carbon cycle ; much of it formed on land ( Section 4.3 ). The preservation of organic material in sediments depends not only on the supply of dead organisms, but also on anoxic chemical conditions where they accumulate.

4.5 Generating carbon — the legacy of volcanoes

What is the origin of the carbon within the carbon cycle ? Figure 1.9 showed that the greatest proportion of the global carbon store is locked into carbonate rocks. Over the 4.5 billion years of the Earth's history, carbon must have moved from the atmosphere into the oceans and thence into carbonates. How did the atmospheric carbon originate?

The Earth's atmosphere as a whole was derived mainly from gases brought to the surface from the Earth's interior. For example, the 1991 eruption of Mount

Etna in Sicily released an estimated 0.01 × 10 12 kg of carbon in the form of CO 2 ( Figure 1.12 ). Most volcanic carbon comes from the steady degassing of lava flows rather than from volcanic vents.

In the short term, volcanic sources release insignificant volumes of CO 2 compared with other fluxes of carbon, but over geological time, degassing of the Earth's interior can reasonably account for all the carbon in the natural surface system.

4.6 The fossil fuel 'bank'

During the period of accumulation of most coal and petroleum, the past few hundred million years, the equivalent of around 10 23 J of chemical energy have been 'banked' by Earth processes. As you have seen in Sections 4.3 and 4.4 carbon is added to these reservoirs continually, at a rate today that is equivalent to about 5 × 10 17 J yr −1 . That rate of growth represents roughly a mere thousandth of present world energy demand.

Question 13

If the consumption of energy from all primary sources in 2002 were 451 EJ, how long would the fossil fuel energy 'bank' last at that rate of consumption?

The fossil fuel energy 'bank' would last (10 23 J)/ (4.51 × 10 20 J yr −1 ), or about 220 years, at this rate of consumption.

In fact, the 'bank' contains only about 0.04% of the amount of organic carbon preserved in sedimentary rocks. However, that total store of buried organic carbon is finely dispersed, at an average concentration of about 0.4% in sedimentary rocks. At that level, it can never be exploited, either economically or with an efficiency that yields more energy than it consumes.

Although buried organic carbon is widely distributed, concentrations sufficient to constitute resources are rare and very restricted in space and geological time relative to small amounts of organic carbon that are present in many sediments.

5 Nuclear energy

Einstein's famous equation E = mc 2 shows that mass ( m ) and energy ( E ) are proportional to one another. The constant c 2 linking the two is the square of the speed of light c (3 × 10 8 m s −1 ). Implicit in the equation is that mass can be converted into energy , and vice versa, although the conversion of energy into mass occurs only in very powerful particle accelerators. The conversion of matter into energy is the basis of nuclear energy . When unstable nuclei split (nuclear fission) the sum of the masses of the isotopes that are produced is slightly less than that of the original fissile isotope. That tiny mass deficit is converted into a relatively huge amount of energy , because c 2 is a very large number (9 × 10 16 m 2 s −2 ). When isotopes fuse at immense temperatures in the interiors of stars, the product again has lower mass than the original isotopes. So both nuclear fission and fusion potentially produce energy that can be exploited, but in both cases the phenomena have to be artificially induced.

The 'fuel' for nuclear fission occurs naturally in the Earth's crust in the form of unstable isotopes of uranium and thorium, added to by other isotopes that are formed artificially inside nuclear reactors. Note that uranium and thorium isotopes naturally break down by emission of various particles (helium nuclei and electrons), as a result of which their 'daughter' isotopes have lower atomic masses and numbers. Some of the 'daughter' isotopes are also unstable and undergo radioactive decay, which eventually results in the formation of several stable isotopes of the element lead. Such radioactive decay is not the same as nuclear fission and occurs at a constant pace. Radioactive decay also releases energy , but at an amount far lower per decayed atom than in nuclear fission. That energy continually heats the Earth's interior ( Section 3.3 ) and is the source of geothermal energy .

Potential 'fuel' for nuclear fusion also occurs naturally in the form of an isotope of hydrogen that includes a neutron as well as a proton in its nucleus, instead of the single proton. This isotope ( 2 H or deuterium ) occurs in tiny amounts in water, and was produced originally by processes early in the history of the Universe.

6 Concentrating, storing and transporting energy

The Earth is awash with energy from sources other than fossil fuels ; thousands of times as much as humans use. Why then do we need to use any other energy supply?

6.1 Concentrating energy

As far as human needs are concerned, there is a marked difference between 'dilute' and 'concentrated' energy . Water vapour in the atmosphere, for example, has considerable potential energy since a huge mass globally (about 13 × 10 15 kg—Smith, 2005) is held high above the Earth's surface. But this potential energy represents a very dilute form of energy ; falling rain could not turn a water wheel. It is only when energy can be 'concentrated' that it can be put to good use — in this case by rainfall accumulating in streams and rivers, or being stored in reservoirs at high elevations. The concentration can be expressed colloquially in terms of energy density , which is the amount of energy stored by a resource divided by the volume of the space that it occupies.

Some forms of energy are relatively difficult to concentrate, so have a low energy density , whereas others are easier to concentrate. The energy contained in moving air is rather difficult to concentrate; windmills and wind farms have to be sited where natural factors enhance wind speed and constancy. Solar power has a low energy density , so requires large collecting devices. The potential energy of rain is naturally concentrated and held in mountain lakes; we concentrate this energy artificially when rainwater is stored in a reservoir. This emphasises why fossil fuels are so valuable as they represent naturally concentrated forms of the solar energy that reached the Earth millions of years ago.

The ultimate form of concentrated energy is matter itself, in the form of nuclear energy .

6.2 Storing and transporting energy

To be useful to us, energy must be available where and when we want it, and in a form and in amounts we can handle. Severe weather systems concentrate natural energy wonderfully, but hurricanes associated with storm- force winds, driving heavy rain, thunder and lightning wreak havoc rather than top up our energy supplies.

Storing most forms of energy is very difficult. We have to re-heat our homes daily in the wintertime because they constantly lose heat, despite our attempts to insulate them. We cannot store light when the Sun goes down; we have to turn electricity into light until the Sun reappears. In fact, only two forms of energy are truly storable. Potential energy can be stored almost indefinitely by mechanical means, as in springs or lifted weights — the basis of clocks. Far more convenient is storage that exploits chemical energy — batteries, or even better, chemical fuel.

Fuels are compounds whose combustion liberates a large amount of energy per unit mass: they commonly have a high energy density . Wood was the major fuel before the Industrial Revolution, and remains the most important fuel for many non-industrial societies today. Wood, and other plants that can be used as fuels , produce biomass energy . As industry develops, energy demands grow and fuels with higher convertible energy content per unit mass are needed. Modern energy supply is centred on the fossil fuels : coal, oil and gas ( Figure 1.4 ). Note that although the isotopes whose fission or fusion forms the basis for nuclear power are not burnt, they are generally known as nuclear fuels .

A further advantage of fuels as energy sources is their transportability, so that conversion can take place on selected sites or in mobile units. Highly concentrated fuels require less energy to transport than those with a low energy density but since lots of energy can be released accidentally from badly handled concentrated energy sources, care has to be taken to ensure that transport is safe. For some applications, such as cars, generating energy from stored chemical energy has the advantage of the ease of transport of small amounts of fuel.

Fossil fuels therefore represent extremely useful energy sources because they have a high energy density , they store energy for very long periods to be used when needed, and they can be transported simply and relatively safely.

A very important form of energy transport in developed countries is the generation and transmission of electricity. Figure 1.6 shows that around one-sixth of energy used in the UK is distributed as electricity via the National Grid. Since every primary energy source is used to some extent in generating electricity, a brief introduction to generators is useful ( Box 1.2 ).

Box 1.2 Electricity generation

By far the greatest contribution to electricity supplies is made by exploiting the way in which an electrical current is induced in a conductor when it is moved through a magnetic field. Most such generators are made up of a cylindrical coil of conducting wire that is rotated between extremely strong magnets, so that an electrical current is induced in the coil ( Figure 1.13a ). There are other means, such as fuel cells and photovoltaic devices, but generators are common to conversion of most kinds of primary energy . Driving the rotation depends on harnessing energy released from primary energy sources through a specific form of engine, the turbine.

A turbine is a rotary engine driven by a moving fluid. A propeller on a boat or an aircraft, or a jet turbine, provides a driving force because of the design of its blades. A turbine used in electricity generation simply exploits the reverse of this effect. Moving 'fluid' provides the force that spins the turbine. The rotation transmits energy , and for electricity generation it is connected to a rotary generator. The simplest turbines have one moving part, as in windmills or water wheels ( Figure 1.13b ).

Electricity generation from flowing water or wind exploits the kinetic energy of the fluid. However, from the 19th century to the present day, the most common turbines used to generate electricity have been driven by high-pressure steam created by boiling water using coal, oil, natural gas, nuclear or geothermal energy (Section 5.1). In some electricity generating stations the moving fluid is the gas produced by burning oil or natural gas, in the manner of a jet turbine, thereby missing out the intermediary of steam and the associated inefficiency. The principle of a steam turbine is somewhat different from those used to harness the energy of wind and flowing water, and so too is its design ( Figure 1.13c ). Steam contains energy in three forms: as heat; as the energy needed to change water's state from liquid to gas ( latent heat of vaporisation ); and as the energy bound up by the compression of a pressurised gas. The last is a form of potential energy , released when the pressure drops, as in the case of the air in a tyre when its valve is opened. Together, these three forms of contained energy are known as the enthalpy . The enthalpy of a gas is given by:

where H is enthalpy (in J), U is heat (including latent heat of vaporisation; in J), P is pressure (in pascals or kg m −1 s −2 ) and V is the volume of steam (in m 3 ). (Note that pressure times volume — in kg m 2 s −2 —gives units in joules.) It is the PV term that provides much of the driving force for a steam turbine, because the pressure gradient across the turbine leads to rapid expansion of the steam and therefore high speed in the flow. Many steam engines, including the original piston engines invented in the early Industrial Revolution, also exploit the latent heat of vaporisation, by condensing the steam at the outlet of the turbine. The change of state from gas to liquid results in a near vacuum that increases the pressure gradient across the turbine — condensation adds 'suction' to the 'blowing' by steam. Latent heat is released and this can be 'recycled' in the generating system.

The late-20th century saw an increased reliance on electricity generation that uses natural gas as a fuel. Gas turbines are similar in design to those used in aircraft jet turbines. Turbines rotated by combustion gases have two important advantages over steam turbines: they are more efficient, and can be turned on and off very quickly, thereby suiting variable demand for electricity. Natural gas also contains a lower proportion of carbon than coal and oil, and so less carbon dioxide is emitted to the atmosphere.

7 Renewable and non-renewable energy supplies

Energy resources can be considered in a completely different way from their energy density — whether or not they are renewable. Some energy sources incorporate energy released comparatively recently from the Sun and are replenished naturally over a timescale of days to tens of years. Therefore solar, wind and wave energy resources, being continually available, are renewable energy supplies. Other examples of renewables are geothermal and tidal energy sources.

Other potential energy resources are legacies of solar power received and converted into stored energy in the geological past; coal is a good example. Coal seams are replenished naturally over a timescale of millions of years. Once coal began to be exploited faster than its rate of creation it became non-renewable and its use at current levels cannot be sustained.

Question 14

Which energy sources mentioned so far are renewable, and which are nonrenewable on the scale of a human lifetime?

Energy sources such as solar, biofuels, hydro, wind, waves, tides, and geothermal are continually replenished, so they are renewable on this timescale. The fossil fuels and nuclear energy are not being replaced on this timescale, so they are non-renewable.

All fossil fuels are slowly being renewed by the death, burial and decay of present plant and animal life, but at an extremely slow rate compared with the pace of human economic activity. The Earth's natural systems may eventually replace all the fossil fuels that humanity has already used, but how and when that might become possible is impossible to judge.

Likewise, only extremely slow geological processes renew fissionable nuclear fuels . The instability of naturally radioactive isotopes such as uranium and thorium, which formed in stars much larger than the Sun during the moment of their destruction as supernovae, results in them gradually diminishing with time. Replenishing the ores of uranium and thorium by geological processes takes hundreds of million years. So, nuclear fuels too are non-renewable. Even the hydrogen isotope deuterium, which is potentially a vast source of energy from thermonuclear fusion, is a 'one-off' legacy resource and is finite. But even so its potential vastly outstrips that of all other non-renewable energy sources.

The distinction between renewables and non-renewables is one of timescale and energy concentration, but it is critical for human society. Think of renewable energy resources as income , and non-renewable energy resources as inheritance . We 'spend' the Earth's energy resources constantly for cooking, travelling, heating or cooling buildings, manufacturing and in many other ways. At present, modern industrial societies generate energy mostly from fossil fuels , thereby depleting an inheritance accumulated from millions of years of 'banked' solar energy and internal heat. Much less energy is currently generated from day-to-day energy 'income', i.e. from renewables: the global energy 'accountancy' has become unbalanced and unsustainable.

Setting aside the environmentally damaging effects of burning fossil fuels , such as atmospheric pollution and global warming, sooner or later present energy generating policy will deplete our stock of fossil fuel. To stay solvent in energy terms over the long term leaves no choice other than to transfer society's day-to-day energy supply to renewable sources, or return to a low- energy society. The other alternative is harnessing energy from nuclear fission or fusion, but that too cannot last indefinitely. This book aims to provide a scientific basis to understanding some of the decisions that will need to be made to enable humanity to stay 'solvent' in energy terms. Yet you will no doubt be well aware that such decisions are not those of individuals, but are presently dominated by economic and political factors, irrespective of the scientific facts.

Energy is the basis of modern society. Other physical resources can only be effectively extracted, processed and transported if there is a ready supply of energy at the right price.

Energy is defined as the capacity to do work , while work is a force acting on an object that causes its displacement (i.e. force × distance). Both energy and work are measured in joules or, more fundamentally, in newton metres. Power (measured in watts, i.e. joules per second) is the rate of doing work or the rate at which energy changes from one form to another.

All conversions of energy are inefficient to varying degrees, so that primary energy consumption far exceeds the useful work that it makes possible.

The Sun is by far the most important source of natural energy on Earth. The solar radiation that reaches the Earth contributes to winds, waves, atmospheric water circulation, atmospheric heating and surface water evaporation, and to organic activity.

The gravitational attractions of the Sun and the Moon combine to produce tides, and rocks in the Earth's interior also generate heat by the decay of radioactive isotopes in them. These are small but potentially exploitable sources of energy .

Fossil fuels are ultimately derived from solar radiation, through photosynthesis and the carbon cycle .

Most of the world's carbon is locked within carbonate rocks. A large amount of carbon also exists as preserved organic carbon, which includes fossil fuels .

Green plants use solar radiation to build carbohydrates and plant tissue from carbon dioxide and water in the atmosphere and dissolved in the oceans, in a process known as photosynthesis . Photosynthesis releases oxygen into the atmosphere and oceans. When they respire, organisms use oxygen to generate energy from food, releasing carbon dioxide and water vapour back into the atmosphere and oceans. These respiratory reactions are the reverse of photosynthesis .

Concentrations of marine phytoplankton occur in the upper sunlit layers of the oceans where upwelling currents bring nutrients. These form the basis of the marine food chain. There is only a build-up of carbon within marine sediments where there is an adequate supply of organic material and where physical conditions are right for its preservation.

Nuclear energy is derived from the conversion of matter into energy and has a very high energy density .

The world is plentifully supplied with solar-derived energy , but most of it is not in a sufficiently concentrated form to be useful to modern industrial society.

Fuels are of immense value because they are concentrated sources of energy (they have a high energy density ) that can easily be stored, transported and used at will. At the current level of technology, energy transport has become an essential aspect of energy use, dominated by electricity. The most convenient way of electricity generation is through the conversion of mechanical motion — most usually produced today from thermal energy — using generators driven by turbines.

Energy sources can be subdivided into renewables, like solar, wind and wave power , and non-renewables, like peat, coal, oil and gas. Renewables are effectively everlasting, but non-renewables are finite.

Click on the link below to open the course glossary.

Open glossary now...

Acknowledgements

Course image: Adrian S Jones in Flickr made available under Creative Commons Attribution-NonCommercial-ShareAlike 2.0 Licence .

Grateful acknowledgement is made to the following sources for permission to reproduce material in this course:

The content acknowledged below is Proprietary (see terms and conditions ) and is used under licence (not subject to Creative Commons licence ).

Figure 1.2 National Railway Museum/Science and Society Picture Library

Figure 1.5a BP (2004) Statistical Review of World Energy 2004

Figure 1.5b Adapted from NASA material

Figure 1.8 Martin Bond/Science Photo Library

Figure 1.12 NASA's Earth Observatory

Figure 1.13b © David Sanger Photography/Alamy

Figure 1.13c Steve Allen/Science Photo Library

The information in this book has been obtained from a wide range of sources, too numerous to mention. However, specific reference is made in the text to the following:

Boyle, G., Everett, B. and Ramage, J. (eds) (2003) Energy Systems and Sustainability, Oxford University Press and The Open University.

Statistics on UK transport. Available online from Department for Transport Statistics [last accessed December 2007].

Harris, S., Bridgeman, F. and O'Reilly, T. (eds) (2002) Britain's Offshore Oil and Gas, UK Offshore Operators Association. Available online at Oil & Gas UK [last accessed April 2011].

Smith, S. (2005) Water: The Vital Resource (Book 3 of S278 Earth's Physical Resources: Origin, Use and Environmental Impact), The Open University, Milton Keynes.

All other material contained within this course originated at the Open University.

This resource was created by the Open University and released in OpenLearn as part of the 'C-change in GEES' project exploring the open licensing of climate change and sustainability resources in the Geography, Earth and Environmental Sciences. The C-change in GEES project was funded by HEFCE as part of the JISC/HE Academy UKOER programme and coordinated by the GEES Subject Centre.

Don't miss out:

If reading this text has inspired you to learn more, you may be interested in joining the millions of people who discover our free learning resources and qualifications by visiting The Open University - www.open.edu/ openlearn/ free-courses

FREE K-12 standards-aligned STEM

curriculum for educators everywhere!

Find more at TeachEngineering.org .

TeachEngineering
Renewable Energy

Lesson Renewable Energy

Grade Level: 4 (3-5)

Time Required: 45 minutes

Lesson Dependency: None

Subject Areas: Earth and Space, Physical Science, Science and Technology

NGSS Performance Expectations:

Print lesson and its associated curriculum

Curriculum in this Unit Units serve as guides to a particular content or subject area. Nested under units are lessons (in purple) and hands-on activities (in blue). Note that not all lessons and activities will exist under a unit, and instead may exist as "standalone" curriculum.

Water Power
Solar Power
Wild Wind! Making Weather Vanes to Find Prevailing Winds
Wind Energy: Making & Testing Pinwheels to Model Wind Turbines
Gone with the Wind Energy: Design-Build-Test Mini Sail Cars!
Build an Anemometer to Measure Wind Speed
Wind Power! Designing a Wind Turbine
Windmill of Your Mind — Distributed Energy Goes to School
Falling Water
Waterwheel Work: Energy Transformations and Rotational Rates
A Case of Innovation: Technical Writing about River Current Power
Stations of Light
Capturing the Sun's Warmth
Cooking with the Sun: Comparing Yummy Solar Cooker Designs
Design and Test Model Solar Water Heaters
Design a Solar City
Power to the People

TE Newsletter

Engineering connection, learning objectives, more curriculum like this, introduction/motivation, associated activities, lesson closure, vocabulary/definitions, user comments & tips.

Engineering… Turning your ideas into reality

Engineers have a good understanding about energy, so they can harness renewable resources to create electricity for use in our everyday lives. Mechanical, electrical and civil engineers collaborate to develop new and more efficient ways to generate electricity from renewable resources. They design cleaner-burning engines and new car designs (such as hybrid cars) that require less fuel and result in improved gas mileage which in turns improves our planet.

After this lesson, students should be able to:

Describe sources and uses of energy.
Define renewable and non-renewable energy.
Provide examples of common types of renewable and non-renewable resources.
Understand and explain general ways to save energy at a personal, community and global level.
Understand and explain, in general terms, how passive solar heating, hydropower and wind power work.
Describe some general characteristics of solar power, hydropower and wind power.
Understand the benefits and disadvantages to using renewable resources.
Explain how engineers design more efficient ways to use generate electricity.
Describe the role of engineers in energy conservation.

Educational Standards Each TeachEngineering lesson or activity is correlated to one or more K-12 science, technology, engineering or math (STEM) educational standards. All 100,000+ K-12 STEM standards covered in TeachEngineering are collected, maintained and packaged by the Achievement Standards Network (ASN) , a project of D2L (www.achievementstandards.org). In the ASN, standards are hierarchically structured: first by source; e.g. , by state; within source by type; e.g. , science or mathematics; within type by subtype, then by grade, etc .

Ngss: next generation science standards - science, international technology and engineering educators association - technology.

View aligned curriculum

Do you agree with this alignment? Thanks for your feedback!

State Standards

Colorado - science.

Brainstorm a list of ideas about where and when we use energy. (Answer: We use energy all the time. Humans use energy to be active – to walk, talk, play basketball, etc. We use energy to power our appliances, vehicles, lights, etc. Cells use energy to perform the most basic life functions. Life as we know it would not be possible without energy production and consumption.)

Energy is everywhere! Although sometimes you can hear energy (sound), feel energy (wind), taste energy (food), and see energy (light), most often it is hard to figure out exactly where energy is.

Energy can move and change, but it cannot be destroyed. Almost every form of energy can be converted into other forms. It is similar to the heat you feel coming off a light bulb while it is on. The warmth is light energy changed to heat energy. Whatever form it is in, energy is essentially the ability for making something happen or, as scientists put it, "doing work."

Where do we get our energy? Well, a lot of energy originally comes from the sun. We get some energy directly from the sun when we use solar panels; however, most energy comes from fossil fuels (coal and oil), which got their energy from fossilized plants and other organisms that obtained their energy directly from the sun by a process called photosynthesis that occurred many years ago. There are many different types of energy, as we brainstormed earlier. Some of these types of energy are called renewable , or can be re-used, such as energy from the sun, wind or water. Other energy is called non-renewable because once it is used up, it is gone, like coal and oil.

A colorful diagram showing the four sources of non-renewable energy. Shown clockwise are an oil pump, indicating oil energy; a hammer and pick, indicating coal energy; a blue flame, indicating natural gas energy; and an atom with electrons swirling around it, indicating nuclear energy.

Now, imagine yourself having surgery in a hospital and the power goes out. This scenario would be terrible. Fortunately, hospitals have backup generators (designed by engineers!) to prevent this from ever happening. Generators are like storage houses for energy and are usually powered by electricity from coal or fossil fuels. Generators are not normally attached to things like stoplights, railcars or computer networks, which is why we sometimes see stoplights that have gone out. Now, imagine that all of the above mentioned things are backed up with solar energy power or another type of stored renewable energy. This stored power, especially in the form of solar power, never becomes overloaded (which is what happens when the lights in your house or neighborhood go out). The renewable source is always supplying more energy; i.e., the sun is almost always shining on some part of the Earth, wind is always blowing, and rivers are always running. Storing renewable energy for power failures is a better idea because those energy supplies will never run out.

Engineers know all about energy and are currently designing new and more efficient ways to generate electricity using renewable resources. They are designing cleaner engines that use less fuel and new car designs that use electric motors. Today, we are going to look at how engineers can use sun, wind and water power to create electricity to run our homes, cars and everything else. Wow! What incredible engineering creativity!

Lesson Background and Concepts for Teachers

What Is Power?

Energy is the ability to do work (applying a force over a distance), to make things happen, to cause change, or to start motion (a change in position of an object with time). It is the capacity for vigorous activity.

Energy can move (be transferred) and change (be transformed), but it cannot be destroyed. Interactions produce changes in a system, although the total quantities of energy remain unchanged. For example, a power station produces electricity by changing the energy from fuel into electrical energy. A gas-fired power station burns gas, converting the gas' chemical energy into heat. Almost every form of energy can be converted into other forms. But whatever form it is in, energy is essentially the capacity for making something happen or, as scientists put it, "doing work."

Energy comes from many sources, directly or indirectly: power plants, people, food, light, windmills, turbines, fires, electrical circuits, the sun, machines, etc. All energy originally comes from natural resources, most of which originate from the sun.

We use energy to heat houses and buildings, provide light, heating water, break down food, play sports, do activities, operate vehicles, etc.

What are the Different Types of Energy?

Biomass is the combustion of materials that originate from living things.
Chemical is used to fuel automobiles and other vehicles.
Electrical drives many small machines and keeps lights glowing.
Geothermal taps steam from water heated underground (like geysers) and uses it to spin turbines.
Hydrogen power uses electricity to break down water into hydrogen gas. The amount of energy released is less than the energy used to break it apart, so not currently feasible.
Hydroelectricity generates electricity by harnessing the power of flowing water (a renewable resource as long as there is rain). Refer to the associated activity Water Power for students to observe and learn about water related methods of harvesting energy.
Kinetic is the energy of motion. A spinning top, a falling object, and a rolling ball all have kinetic energy. The motion, if resisted by a force, does work. Wind and water both have kinetic energy. Refer to the associated activity Wind Power to give students an understanding of how wind energy is harvested and used.
Light energy is generated from light bulbs and computer screens, the sun.
Nuclear fusion imitates the method the sun uses to produce energy. It involves the joining together of the nuclei of hydrogen atoms.
Nuclear fission is when energy is given off from splitting nuclei of uranium atoms.
Potential energy is the energy stored by an object as a result of its position. For example, roller coaster at the top of a hill.
Sound energy is created, for example, when a door slams, it releases sound energy.
Solar energy occurs from the sun (light). Refer to the associated activity Solar Power for students to explore this energy form.
Thermal energy (or heat) boils water, keeps us warm and drives engines.
Tidal energy is when the energy from ocean tides is harnessed.

Other energy sources, for example, include energy created from old car tires: this source fuels five power stations in the U.S. Also, engineers are trying to design new gas power stations (gas drives the electricity generators and then is reused to heat the plant). Lastly, methane that is produced in sanitary landfills may be used to make power.

How are Energy Sources Categorized?

What are Engineers Doing to Improve Our Energy Sources?

Current uses of fossil fuels have catastrophic effects on our environment. Obtaining and using them destroys natural habitats and pollutes the air, water, and land. We can reduce this consumption of fossil fuels by finding alternative, renewable methods of energy production. Engineers are involved in many new technologies that will save our precious resources from devastating long-term effects.

And, engineers are improving the design of factories and products to make even more efficient use of our resources. They are designing cleaner engines that use less fuel and new car designs that run by electric motors. They are studying corals because they very efficiently use low levels of phosphate in the water for energy. Corals have fractal surfaces, and scientists believe that fractal surfaces could make many chemical reactions more efficient. They are working to make machines smaller and more efficient (industrial engineers/designers). For example, they developed fiber optics (thin glass cables to replace heavy metal ones for phones). These efforts contribute to a better, cleaner planet for all inhabitants. Wouldn't it be great to be an engineer making such an important difference in our lives?

Watch this activity on YouTube

Ask the students to describe some sources of renewable energy? (Answer: sun, wind, water) Can they list three specific ways that engineers are involved with renewable resources? (Possible answers: engineers study renewable resources to develop better ways to use these resources for energy generation; engineers design cars that run off renewable resources; engineers design generators that store the energy gathered from renewable resources; engineers develop wind farms to generate electricity for us to use; engineers develop hydropower plants to generate electricity for us to use; engineers are developing machines that are more efficient to reduce the amount of energy, renewable or non-renewable, that gets used; and engineers work to inform communities about what they can do to help conserve energy and use renewable resources.) Engineers work at developing new technologies that use renewable sources to contribute to greater health, happiness and safety of our Earth's inhabitants.

absorb: To be taken into a material without transmission or reflection.

active solar system: Solar power systems that use electrical or mechanical components, such as fans, pumps, and electrical controls in circulating fluids. These systems can be used for heating water or heating/cooling buildings.

anemometer: An instrument for measuring the velocity of wind.

convection: The transfer of thermal energy in a fluid (gas or liquid) by the circulation of currents in the heated fluid causing warmer packets to rise while cooler packets sink.

electromagnetic radiation: Electromagnetic energy transmitted in the form of waves or particles (photons); the electromagnetic spectrum, in order of increasing energy: radio waves, microwaves, infrared radiation, visible light, ultraviolet radiation, x-rays, gamma rays, cosmic-ray photons.

generator: A device that transforms mechanical energy into electrical energy.

heat exchanger: A device, such as an automobile radiator, that transfers heat from one liquid to another without allowing them to mix.

heat-transfer fluid: A fluid circulated in a heat exchanger; this fluid gains energy from one region and transfers it to another region.

hydraulic head: The difference in depth of a liquid at two given points; the pressure of the liquid at the lower point expressed in terms of this difference.

insulation: A material used to prevent the passage of heat, electricity, or sound (i.e., a non-conducting material).

passive solar system: Solar power systems that do not require electrical or mechanical components; these systems can be used for heating water or heating/cooling buildings.

penstock: A pipe or conduit used to carry water to a water wheel or turbine.

photovoltaic system: This is a system which converts solar energy into electricity.

reflect: This is when something such as sound waves or light waves bend back or return upon striking a surface.

regenerate: To re-grow or replace.

renewable energy: Energy that is made from sources that can be regenerated or reused is renewable.

rotor: The rotating part of an electrical or mechanical device is the rotor.

thermal mass: Materials that store thermal energy, such as water, concrete, brick, stone, adobe, tile, etc.

transmit: To allow the passage through a material.

turbine: A machine in which the kinetic energy of a moving fluid is converted into mechanical energy by causing a series of buckets, paddles, or blades on a rotor to rotate.

Pre-lesson assessment

Brainstorming: Ask students to brainstorm ideas about where and when we use energy. (Possible answers: We use energy all the time. Humans use energy to be active – to walk, talk, play basketball, etc. We use energy to power our appliances, vehicles, lights, etc. Cells use energy to perform the most basic life functions. Life as we know it would not be possible without energy production and consumption.)

Post-introduction assessment

Guess the Amount!: Ask students the following questions and ask them to guess at the different percentages of energy use. Discuss and explain the answers.

What percent of the energy the world uses today is derived from fossil fuels (e.g., coal, oil, natural gas)? (Answer: 80-85%. This means that only 15-20% of the energy we use is from renewable energy sources such as sun, wind and water.)
The U.S. has less than 5% of the world's population. What percent of the world's energy do we use? (Answer: Around 17%. This means that the U.S. uses a lot more energy than other countries. Why do the students think that is? Discuss the amount of toys, appliances and other electric powered items in a single person's home.)
What percent of the electricity consumed in the U.S. is used for light bulbs? (Answer: 5%. This means that we leave a lot of light bulbs on when unused. Can the students think of a time where they could save some electricity by turning off a light bulb?)

Discussion: Ask students the following questions. Discuss the answers.

How do we know the energy is there? (Answer: We can see it, feel it, hear it, etc.)
Ask students to describe where this energy comes from. (Answer: ultimately all of it comes from natural resources (renewable and non-renewable), but it is often moved (transferred) and changed (transformed) in the process. You may want to give an example here like coal being mined from the earth, sent to power plants where it is burned to produce steam. The steam turns a turbine and produces electricity that is sent to our houses via power lines, and used in our electrical items like a refrigerator. Or how solar energy is used by plants to create food so they can grow and then we, in turn, use the plants as food to provide energy for our bodies.)
Ask students to describe where they get their energy. (Answer: from food) Ask them to describe what might happen if suddenly there was no more food. (Note: this is a stretch for some because generally food is considered a renewable resource and because the food supply often seems unlimited to people in the U.S.). What would they do? (Answer: Become hungry, eventually starve, engineer some new source of nutrients, etc.) How would they feel? (Answer: Hungry, sad, scared, motivated to find a way to survive, etc.)
What if there was only a tiny bit of food? How would it get distributed? Who would decide? What are some other consequences? (Answer: equal world-wide distribution, war, the rich get it, others die, new source of nutrients discovered/engineered, etc.)

Lesson summary assessment

Future Timeline: Ask students to work in a group to imagine what today would be like if there were no electricity (permanently, not just a blackout situation). Ask them to develop a timeline describing what this typical day might be like. Ask them to really consider how they would feel and what they would do. Ask each group to present their timeline to the class.

Venn Diagram: Ask students to create a Venn Diagram to compare/contrast a form of renewable energy and a form of non-renewable energy. They should provide as many facts and details as they can.

Save a Watt: Ask students to engage in two energy saving activities before the next class period. Ask them to describe in detail the impact these actions had during the next class. You can have the students list the activities or write a paragraph and turn the assignment in.

Lesson Extension Activities

Write and illustrate a children's story for 8-10 year olds about life in the year 2100. It should describe life without fossil fuels and should identify the energy sources used in everyday life as well as some type of conservation measures.
Discuss what is happening with our world energy supply from fossil fuels and other non-renewable resources. (Examples: fossil fuels are being dangerously depleted, the rich countries receive a larger share of the energy and are more wasteful with it, wars are developing; e.g., the Gulf War, scientists and engineers are researching and developing renewable energy sources, etc.)
Check out the awesome information and activities/games at Environmental Education for Kids (EEK) website from Wisconsin Department of Natural Resources at dnr.wi.gov
Check out some of the activities at Watt Watchers: https://www.watt-watchers.com/student-activities/
Check out some of the activities and games about energy online
Play energy-themed games at NASA's Climate Kids website: https://climatekids.nasa.gov/menu/energy/
Learn more about renewable energy at Alliant Energy's website: https://www.alliantenergykids.com/RenewableEnergy/RenewableEnergyHome
Read, color, and solve puzzles in the "Saving Energy in My Home Coloring and Activity Book" at https://extension.colostate.edu/docs/pubs/consumer/saving-energy-home.pdf
Try a Nuclear Chain Reaction activity at http://nuclearconnect.org/in-the-classroom/for-teachers/nuclear-chain-reaction-using-dominoes

Students explore the outermost planets of our solar system: Saturn, Uranus and Neptune. They also learn about characteristics of Pluto and its interactions with Neptune. Students learn a little about the history of space travel as well as the different technologies that engineers develop to make spa...

Students are introduced to the fabulous planet on which they live. They learn how engineers study human interactions with the Earth and design technologies and systems to monitor, use and care for our planet's resources wisely to preserve life on Earth.

Students are introduced to the International Space Station (ISS) with information about its structure, operation and key experiments.

preview of 'Life in Space: The International Space Station' Lesson

Students learn the metric units engineers use to measure mass, distance (or length) and volume. They make estimations using these units and compare their guesses with actual values. To introduce the concepts, the teacher needs access to a meter stick, a one-liter bottle, a glass container that measu...

preview of 'Measure Twice, Cut Once' Lesson

American Wind Association, www.awea.org

Boulder Community Network, Environmental Center, bcn.boulder.co.us/environment/

California Energy Commission, www.energyquest.ca.gov/

Energy Information Administration, Energy Kid's Page, www.eia.gov/kids/

Hewitt, Paul G. Conceptual Physics, Boston, MA: Addison Wesley Publishing Company, 2004.

Goswami, D. Yogi, Kreith, Frank, and Kreider, Jan F. Principles of Solar Engineering, Taylor & Francis Group, 2nd edition, 2000.

Graham, Ian, Taylor, Barbara, Fardon, John, Oxlad, Chris and Parker, Steve. Science Encyclopedia, Miles Kelly, 2000.

Milton Hydro, https://www.miltonhydro.com/Residential/Community/Power-Kids

National Renewable Energy Laboratory, www.nrel.gov

Snow, Theodore. The Dynamic Universe: An Introduction to Astronomy, Minnesota: West Publishing Company, 1988.

Steen, Anthena S., Steen, Bill, Bainbridge, David and Eisenberg. The Straw Bale House, Vermont: Chelsea Green Publishing Company, 1994.

Texas State Energy Conservation Office, www.infinitepower.org/lessonplans.htm

U.S. Department of Energy, energy.gov

U.S. Department of Energy, Energy Efficiency and Renewable Energy, www.eere.energy.gov

Contributors

Supporting program, acknowledgements.

The contents of this digital library curriculum were developed under a grant from the Fund for the Improvement of Postsecondary Education (FIPSE), U.S. Department of Education and National Science Foundation GK-12 grant no. 0338326. However, these contents do not necessarily represent the policies of the Department of Education or National Science Foundation, and you should not assume endorsement by the federal government.

Last modified: January 19, 2024

If you're seeing this message, it means we're having trouble loading external resources on our website.

If you're behind a web filter, please make sure that the domains *.kastatic.org and *.kasandbox.org are unblocked.

To log in and use all the features of Khan Academy, please enable JavaScript in your browser.

AP®︎/College Environmental science

Course: ap®︎/college environmental science > unit 5.

Renewable and nonrenewable energy resources

Renewable and nonrenewable energy sources

Global energy use
Intro to energy resources and consumption
Nonrenewable energy sources are those that are consumed faster than they can be replaced. Nonrenewable energy sources include nuclear energy as well as fossil fuels such as coal, crude oil, and natural gas. These energy sources have a finite supply, and often emit harmful pollutants into the environment.
Renewable energy sources are those that are naturally replenished on a relatively short timescale. Renewable energy sources include solar, wind, hydroelectric, and geothermal energy. They also include biomass and hydrogen fuels. These energy sources are sustainable and generate fewer greenhouse gas emissions than fossil fuels.

Want to join the conversation?

Upvote Button navigates to signup page
Downvote Button navigates to signup page
Flag Button navigates to signup page

Natural Sources Of Energy

Sources of Energy

The sun is the main source of energy on Earth. Other energy sources include coal, geothermal energy, wind energy, biomass, petrol, nuclear energy, and many more. Energy is classified into various types based on sustainability as renewable sources of energy and non-renewable sources of energy.

What Is Energy?

The classical description of energy is the ability of a system to perform work, but as energy exists in so many forms, it is hard to find one comprehensive definition. It is the property of an object that can be transferred from one object to another or converted to different forms but cannot be created or destroyed. There are numerous sources of energy. In the next few sections, let us discuss the about different sources of energy in detail.

Sources Of Energy

Sources of energy can be classified into:

Renewable Sources
Non-renewable Sources

Renewable sources of energy are available plentiful in nature and are sustainable. These resources of energy can be naturally replenished and are safe for the environment.

Examples of renewable sources of energy are : Solar energy, geothermal energy, wind energy, biomass, hydropower and tidal energy.

A non-renewable resource is a natural resource that is found underneath the earth. These type of energy resources do not replenish at the same speed at which it is used. They take millions of years to replenish. The main examples of non-renewable resources are coal, oil and natural gas.

Examples of non-renewable sources of energy are: Natural gas, coal, petroleum, nuclear energy and hydrocarbon gas liquids.

Difference between Renewable and Non-renewable Sources of Energy

Natural sources of energy.

During the stone age, it was wood. During the iron age, we had coal. In the modern age, we have fossil fuels like petroleum and natural gas. So how do we choose the source of energy?

Good sources of energy should have the following qualities:

Optimum heat production per unit of volume/mass used
Easy to transport
Least Polluting

Types of Natural Sources of Energy

There are two types of natural sources of energy classified by their popularity and use,

Conventional Sources of Energy
Non-Conventional Sources of Energy

Difference between Conventional and Non-conventional Sources of Energy

In this article, you learned about natural resources, energy sources, and what makes a good source of energy. Explore more such articles at BYJU’S, which provides detailed solutions to the questions of NCERT Book for the energy source so that one can compare their answers with the sample answers given for this chapter.

Frequently Asked Questions – FAQs

What sources of energy are renewable.

Biomass energy
Wind energy
Tidal energy
Hydro energy

What is the main source of energy in India?

What are the sources of energy in india.

Following are the sources of energy in India:

Natural gas
Thermal energy
Mineral oil

Can any source of energy be pollution-free?

What are the advantages and disadvantages of wind power.

There are no harmful gases released into the environment.
It is a way for the generation of revenue in the local communities.
It is one of the clean sources of energy.

Disadvantages:

The storage of energy needs to be improved.
The initial setup requires a lot of investment.
Numerous lands will be used up.

List the examples of sources of energy

Biofuel energy
Geothermal energy
Solar energy
Nuclear energy

Watch the video and find out conservation measures we can take to save the natural resources depleting at an alarming rate.

Stay tuned with BYJU’S for more such interesting articles. Also, register to “BYJU’S – The Learning App” for loads of interactive, engaging Physics-related videos and unlimited academic assistance.

Put your understanding of this concept to test by answering a few MCQs. Click ‘Start Quiz’ to begin!

Select the correct answer and click on the “Finish” button Check your score and answers at the end of the quiz

Visit BYJU’S for all Physics related queries and study materials

Your result is as below

Request OTP on Voice Call

Register with BYJU'S & Download Free PDFs

Skip to global NPS navigation
Skip to the main content
Skip to the footer section

Exiting nps.gov

Rate the lesson plan, teacher reference materials, resources and energy.

Klondike Gold Rush National Historical Park

Teachers can use these worksheet templates to help students understand resource and energy use. One worksheet provides a Venn diagram template with U.S. Energy Consumption source graph, and another worksheet provides a chart template for students to record information on different types of energy sources. There is also an energy research project assignment with rubric.

A resource is a source or supply from which benefit is produced . The key word here is “benefit.” Benefit can mean an economic gain, a biological obligation, or of a spiritual value to name a few. Benefit is very subjective and can be defined in many ways; the variety of definitions from students should highlight this. The difference between a nonrenewable resource and one that is renewable is time . Time is also subjective, but here we draw the line at a human timescale (seconds, hours, decades), rather than a geologic time scale (millions of years, billions of years). To be classified as renewable, a resource needs to be replenished through biological reproduction or other naturally recurring processes . A nonrenewable resource is one that cannot be replenished at a sufficient rate for human consumption or use . It is important to note that a traditionally renewable resource can be used at such a rate that would render it nonrenewable. The rate of consumption would then be unsustainable and would put the future of that resource at risk. Sustainability is a watershed word in environmental science. Sustainability is the capacity to endure ; the ability to sustain literally. When applied to resources, sustainability refers to the rate of consumption being at or below levels of replenishment. Energy is defined as the ability to do work. Our energy is largely derived from our natural resources, renewable and nonrenewable alike. The increasing consumption of these resources is becoming a problem as the population increases and world living standards rise. Americans consume 26% of the world's energy, despite having only roughly 4.5% of the world's population; the average American consumes 40 times the resources as a citizen from a 3rd world or developing country.

Additional Resources

Carbon Footprint Calculator

Download Resources and Energy Worksheet with Venn Diagram Template

Download Energy Chart (Different types of energy sources)

Download Energy Research Project

Lesson Plans

Last updated: August 25, 2015

NPTEL courses
IIT Workshops
Partnering courses

Course list

Energy Resources, Economics and Environment

₹ 3,000.00

Prof. Rangan Banerjee IIT Bombay

*Additional GST and optional Exam fee are applicable.

Description

Additional information, certification process, course details.

Reviews (0)

INTENDED AUDIENCE

About the instructor.

Rangan Banerjee is the Forbes Marshall Chair Professor and Head of the Department of Energy Science and Engineering at the Indian Institute of Technology Bombay .He works on energy efficiency and renewable energy, modelling of energy systems, energy planning and policy

1. Join the course Learners may pay the applicable fees and enrol to a course on offer in the portal and get access to all of its contents including assignments. Validity of enrolment, which includes access to the videos and other learning material and attempting the assignments, will be mentioned on the course. Learner has to complete the assignments and get the minimum required marks to be eligible for the certification exam within this period.

COURSE ENROLMENT FEE: The Fee for Enrolment is Rs. 3000 + GST

2. Watch Videos+Submit Assignments After enrolling, learners can watch lectures and learn and follow it up with attempting/answering the assignments given.

3. Get qualified to register for exams A learner can earn a certificate in the self paced course only by appearing for the online remote proctored exam and to register for this, the learner should get minimum required marks in the assignments as given below:

CRITERIA TO GET A CERTIFICATE Assignment score = Score more than 50% in at least 9/12 assignments. Exam score = 50% of the proctored certification exam score out of 100 Only the e-certificate will be made available. Hard copies will not be dispatched.”

4. Register for exams The certification exam is conducted online with remote proctoring. Once a learner has become eligible to register for the certification exam, they can choose a slot convenient to them from what is available and pay the exam fee. Schedule of available slot dates/timings for these remote-proctored online examinations will be published and made available to the learners.

EXAM FEE: The remote proctoring exam is optional for a fee of Rs.1500 + GST. An additional fee of Rs.1500 will apply for a non-standard time slot.

5. Results and Certification After the exam, based on the certification criteria of the course, results will be declared and learners will be notified of the same. A link to download the e-certificate will be shared with learners who pass the certification exam.

CERTIFICATE TEMPLATE

Books and References

There are no reviews yet.

Your review *

Name *

Email *

Save my name, email, and website in this browser for the next time I comment.

Course Name: Energy Resources, Economics and Environment

About Course
Certificate Type
Toppers list
Registration

Course abstract

This course will equip students with the tools necessary for economic analysis and quantification of impacts of energy systems. We will review the availability of energy resources and study methods for quantification of resource depletion and scarcity. The course will cover basic concepts in economics and their application to energy systems. Tools and techniques for project economics for an individual/ company perspective and macro-decision making for society will be introduced. We will discuss basic concepts of welfare economics and environmental economics that are necessary for energy systems analysis and their environmental impacts.

Course Instructor

Prof. Rangan Banerjee

Teaching assistant(s), course duration : jan-apr 2021, view course, syllabus, enrollment : 18-nov-2020 to 25-jan-2021, exam registration : 15-jan-2021 to 12-mar-2021, exam date : 24-apr-2021, course statistics will be published shortly, certificate eligible, certified category count, successfully completed, participation.

Category : Successfully Completed

Category : Elite

Category : Silver

Category : Gold

Final score calculation logic.

Final Score(Score on Certificate)= 75% of Exam Score + 25% of Assignment Score

VINIT SUHAS JAIN 90%

MAULANA AZAD NATIONAL INSTITUTE OF TECHNOLOGY, BHOPAL

SHIVESH SUMBLY 87%

J. C. BOSE UNIVERSITY OF SCIENCE AND TECHNOLOGY, YMCA, FARIDABAD

VIKASH KANDHWAY 77%

Dassault Systemes Solutions Lab Private Ltd

MAYANK BRADIYA 76%

INDIAN INSTITUTE OF TECHNOLOGY,BOMBAY

PRASHANT PRAVESH SALVE 75%

PRANEETH KUMAR MANDARI 73%

VISHNU TEJA DESOOLA 70%

Enrollment Statistics

Total enrollment: 2045, registration statistics, total registration : 448, assignment statistics, score distribution graph - legend, assignment score: distribution of average scores garnered by students per assignment., exam score : distribution of the final exam score of students., final score : distribution of the combined score of assignments and final exam, based on the score logic..